To blend raw material for plywood adhesives at higher rates with greater uniformity, the Willamette Valley Company replaced a ribbon blender that agitates material with a rotary batch mixer that tumbles it.

The company, also known as Wilvaco, the global forest products corporation, mixes fine mesh bark powder from the Western Red Alder tree, along with other wood material, to produce dry blends that it ships to customers who formulate plywood adhesives.

Examples of the products blended include Modal SPR-Dark and Modal SPR-Lite, both bulking agents for plywood glue mixes.

Need for quality & high throughput

“We wanted pure blending in high volume,” said Don Coleman, Willamette Valley Company plant manager. “Our glue customers are very particular when it comes to their ingredients, so consistent quality is important. The ribbon blender did not mix materials thoroughly enough. The material, which customers mix in vats in their own formulations, could clog filters and shut down lines if not properly blended.”

The Munson model 700-TH-140-MS at Willamette Valley blends uniformly in about four minutes, with throughput of 6,000 pounds (2,721 kilograms) per batch. Capacity of the previous ribbon blender was one-third of that amount, and was being outpaced by demand.

Rotary batch mixer

The 140-cubic-foot (4 cubic meter) rotary batch mixer installed at Willamette Valley Company delivers uniform blends in high volumes.

Continuous rotation prevents segregation, reduces energy consumption

Coleman said the mixer’s ability to continue rotating during loading and discharging prevents segregation of materials of varying densities, yielding a homogenous blend. Importantly, Willamette Valley is blending wood powder with particle sizes as small as 200 mesh (74 microns) – finer than baking flour – without densification.

The constant rotation also means energy consumption remains stable and relatively low, especially when making multiple batches of one blend. The soft-start of the motor and slow mixing speed further increase energy savings, said Coleman.

He learned about the rotary batch mixer from the plant manager at Idaho Milling and Grain, a Wilvaco company in Malad, Idaho, that blends wheat flour for glue extenders. Coleman wanted to replace the ribbon blender with a faster, higher throughput machine and his colleague, citing Idaho Milling’s experience, recommended the rotary batch mixer. Given the mixer’s high output, uniform blend quality and short cycle times, Wilvaco made the investment.

Rotary batch mixer

Mixer inlet (foreground) receives material from feed hoppers above.

Material handling system feeds mixer

When tree bark – or “hog fuel” as the industry calls it – is delivered to the plant, operators run it through a 3,600 rpm grinder for cleaning and size reduction. The moisture content of the bark is 45 to 60 percent, so the powder is transported to a dryer, which reduces moisture to 6 to 7 percent. The bark powder is loaded into a distribution bin and conveyed to one of three programmable-logic-controlled (PLC) hoppers that supply the mixer.

Each hopper has a capacity of 3,000 pounds (1,362 kilograms) and is mounted on load cells. A rotary air lock at each hopper outlet discharges material into the mixer’s inlet chute. Coleman said an operator selects a recipe on the computer and pushes a “go” button, causing material to discharge from the feed hoppers. A PLC receives weight loss information from load cells and automatically stops the rotary valves once an accurate batch weight has been discharged.

As the drum rotates, proprietary mixing flights lift, cut, fold and tumble the material, achieving complete blend uniformity in one to three minutes.

The internal flights also serve to elevate the material for discharge through a pneumatically actuated plug gate valve, leaving no residual other than dust. “Some fine dust may be left on the flights, but this can be vacuumed away when the machine shuts down for material changeover,” Coleman said. “A side access door provides access to all interior surfaces for cleaning and inspection.”

From the mixer discharge, a pneumatic conveyor transports blends 14 feet (4.3 meters) vertically to an overhead weigh hopper equipped with load cells and a rotary valve that allows filling of 50-pound (23- kilogram) paper sacks or 3,000-pound (1,362- kilogram) bulk bags under PLC control.

Rotary batch mixer

Mixing flights lift, cut, fold and tumble the material achieving blend uniformity in one to three minutes.

Coleman said 48,000 pounds (21,792 kilograms) of material can be blended in eight hours. “We could do more, but we continually test batch samples and double-check our products to ensure consistent quality,” he said.

Steve Knauth is marketing manager at Munson Machinery Co. Inc. Established in 1823, Munson Machinery specializes in mixers, blenders and size reduction equipment for bulk solids materials. Munson offers 17 high-performance equipment lines, each with numerous models to meet specialized requirements in the chemical, pharmaceutical, nutritional and food and dairy industries.

Munson Machinery Co. Inc.

Willamette Valley Company